---
title: "Whirlpool-built Kenmore washer error code F3 E2"
description: "Whirlpool-built Kenmore washer error code F3 E2: whirlpool wrote this code, not Kenmore."
url: "https://kenmoremiami.support/error-codes/whirlpool-washer-f3-e2/"
date_modified: "2026-09-01"
Appliance type: "Washers"
---


# Whirlpool-built Kenmore washer error code F3 E2

### Whose code this actually is

Kenmore did not write F3 E2, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

### What it means

The hot and cold inlet hoses are connected the wrong way around — the same finding as HC, reported by a machine that shows numbered codes.

### Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to F3 E2 and no other manufacturer’s does.

### Worth trying yourself, in this order

- Swap the hoses at the machine.

### Where this usually goes

The job this most often becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears F3 E2, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

### Where this meaning came from

Whirlpool’s own documentation: *Top Load HE Washer error codes — Whirlpool Product Help*. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

What this one means

Whose code this actually is

Kenmore did not write F3 E2, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

What it means

The hot and cold inlet hoses are connected the wrong way around — the same finding as HC, reported by a machine that shows numbered codes.

Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to F3 E2 and no other manufacturer’s does.

Worth trying yourself, in this order

Swap the hoses at the machine.

Where this usually goes

The job this most often becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears F3 E2, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

Where this meaning came from

Whirlpool’s own documentation: Top Load HE Washer error codes — Whirlpool Product Help. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

---

**[Read full article: Whirlpool-built Kenmore washer error code F3 E2](https://kenmoremiami.support/error-codes/whirlpool-washer-f3-e2/)**