---
title: "Whirlpool-built Kenmore washer signal Fd"
description: "Whirlpool-built Kenmore washer signal Fd: fd is an indicator rather than an error."
url: "https://kenmoremiami.support/error-codes/whirlpool-washer-fd/"
date_modified: "2026-09-01"
Appliance type: "Washers"
---


# Whirlpool-built Kenmore washer signal Fd

### Whose code this actually is

Kenmore did not write Fd, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

### What the appliance is telling you

The machine is in factory default settings — it has been reset to how it left the factory.

This one is an indicator rather than an error. It is published in the same table as genuine problems, and treating it as one is how a working appliance gets a service call.

### Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to Fd and no other manufacturer’s does.

### What happens next

- Run through the setup again.
- It usually follows a control replacement or a power event.

### Where this usually goes

The job this most often becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears Fd, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

### Where this meaning came from

Whirlpool’s own documentation: *Top Load HE Washer error codes — Whirlpool Product Help*. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

What the machine is telling you

Whose code this actually is

Kenmore did not write Fd, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

What the appliance is telling you

The machine is in factory default settings — it has been reset to how it left the factory.

This one is an indicator rather than an error. It is published in the same table as genuine problems, and treating it as one is how a working appliance gets a service call.

Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to Fd and no other manufacturer’s does.

What happens next

Run through the setup again.

It usually follows a control replacement or a power event.

Where this usually goes

The job this most often becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears Fd, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

Where this meaning came from

Whirlpool’s own documentation: Top Load HE Washer error codes — Whirlpool Product Help. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

---

**[Read full article: Whirlpool-built Kenmore washer signal Fd](https://kenmoremiami.support/error-codes/whirlpool-washer-fd/)**