---
title: "Whirlpool-built Kenmore washer error code HC"
description: "Whirlpool-built Kenmore washer error code HC — whirlpool wrote this code, not Kenmore."
url: "https://kenmoremiami.support/error-codes/whirlpool-washer-hc/"
date_modified: "2026-09-01"
Appliance type: "Washers"
---


# Whirlpool-built Kenmore washer error code HC

### Whose code this actually is

Kenmore did not write HC, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

### What it means

The hot and cold inlet hoses have been connected the wrong way around.

### Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to HC and no other manufacturer’s does.

### Worth trying yourself, in this order

- Swap the hoses at the machine.
- It is almost always a recent installation or a recent move, and it is worth checking before anything else.

### Where this usually goes

The job this most often becomes is [diagnostic visit](/services/diagnostic-visit/), and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears HC, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

### Where this meaning came from

Whirlpool’s own documentation: *Top Load HE Washer error codes — Whirlpool Product Help*. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

What this one means

Whose code this actually is

Kenmore did not write HC, because Kenmore has never built an appliance. This one is Whirlpool’s, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.

What it means

The hot and cold inlet hoses have been connected the wrong way around.

Which Kenmore models can raise it

The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool’s, which is why Whirlpool’s table is the one that applies to HC and no other manufacturer’s does.

Worth trying yourself, in this order

Swap the hoses at the machine.

It is almost always a recent installation or a recent move, and it is worth checking before anything else.

Where this usually goes

The job this most often becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears HC, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.

Where this meaning came from

Whirlpool’s own documentation: Top Load HE Washer error codes — Whirlpool Product Help. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer’s document instead.

---

**[Read full article: Whirlpool-built Kenmore washer error code HC](https://kenmoremiami.support/error-codes/whirlpool-washer-hc/)**