Error code
Whirlpool-built Kenmore washer error code LdL
Whirlpool wrote this code, not Kenmore. On a washer wearing this badge, LdL means: The lid lock will not lock. The machine will not wash or spin until it can confirm the lid is secured. Which model prefixes can raise it, and
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code LdL, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
The code
LdL
The lid lock will not lock. The machine will not wash or spin until it can confirm the lid is secured.
or call (305) 680-1018
What it narrows down to
The lid lock will not lock
What you are probably seeing
Diagnostic
From $95, credited to the repair
What it looks like from the kitchen
The symptom this code usually arrives with
A code names the subsystem; the symptom is what sent you to look at the display in the first place. That page says what it usually turns out to be, cheapest cause first.
-
The load comes out soaking Washer will not spin
The cheap answers come first here and they are right most of the time. Every washer refuses to spin rather than risk it, so the things that stop a spin are mostly safety interlocks and load balance rather than the drive.
- Balance and the lock before the drive
- Two builders, two drive systems
- The motor is rarely the answer
On the same appliance
What else belongs to the washers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Too many suds in the drum
The load is too large for the machine to handle
The load is out of balance and the machine
The washer is taking too long to fill, or
The washer is taking too long to drain —
The lid cannot unlock — the machine has detected
The cycle was interrupted by a power failure
The hot and cold inlet hoses have been connected
A reminder that the Clean Washer cycle is due
The lid was left open
The cycle was paused or canceled
The control lock is on, so the buttons do nothing
The same digits mean different things on different equipment. Search the full code list
In more detail
About Whirlpool-built Kenmore washer error code LdL
Whose code this actually is
Kenmore did not write LdL, because Kenmore has never built an appliance. This one is Whirlpool's, and it appears on the washer that Whirlpool built and Sears sold under the Kenmore badge. Whirlpool-built and LG-built washers wear one badge and share almost none of their code scheme, so the wrong table here sends you to a pump when the machine is reporting a lid.
What it means
The lid lock will not lock. The machine will not wash or spin until it can confirm the lid is secured.
Which Kenmore models can raise it
The Kenmore washer whose model number begins 110 — the three digits before the period on the rating plate. Those digits are Whirlpool's, which is why Whirlpool's table is the one that applies to LdL and no other manufacturer's does.
The other ways it may be written
The same condition is published under more than one label, because it has been carried across generations of the appliance and because a segment display draws some characters oddly: dLO, dL. They are the same finding and they lead to the same place.
What happens next
- Check nothing is caught under the lid, and that the strike is not bent.
- Cut the power for thirty seconds and try again.
- A lock that never engages is an inexpensive part and a straightforward repair.
Where this usually goes
The job this most often becomes is washer lock and lid switch repair, and that page carries a starting figure and the reasons that move it. A Kenmore washer in this county works in hard water and a warm laundry room, so a code that arrives with slow draining or long cycles is very often the supply or the drain rather than the machine. Photograph the display before you cut the power: a reset clears LdL, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.
Where this meaning came from
Whirlpool's own documentation: Top Load HE Washer error codes — Whirlpool Product Help. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer's document instead.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards