Error code
LG-built Kenmore dryer error code Ps
LG wrote this code, not Kenmore. On a dryer wearing this badge, Ps means: LG's own label is POWER ERROR. Which model prefixes can raise it, and what to do next.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
What we can confirm
Code Ps, from the manufacturer's own documentation
A code is only meaningful together with the machine showing it — the same digits mean different things on different equipment.
What it narrows down to
LG's own label is POWER ERROR
What you are probably seeing
Diagnostic
From $95, credited to the repair
What it looks like from the kitchen
The symptom this code usually arrives with
A code names the subsystem; the symptom is what sent you to look at the display in the first place. That page says what it usually turns out to be, cheapest cause first.
-
It tumbles perfectly and nothing gets warm Dryer with no heat
A dryer that turns but does not heat has a short list of causes, and which list depends on whether it is gas or electric. Telling us which you have on the phone means the right parts arrive on the first visit.
- Gas and electric fail in different places
- An electric dryer on one leg of supply does exactly this
- The vent is checked in the same visit, always
On the same appliance
What else belongs to the dryers
On this make a code belongs to the appliance rather than to a product line. These are the other conditions this machine can display, and the models that can show this one — a display often has more than one thing to say, and the model number decides what any of it costs to put right.
Other codes this appliance can display
Restricted air flow
A problem with the heater or the heater relays
Low or no line voltage
Whirlpool's wording: five consecutive loads were dried without the
Whirlpool identifies this as an inlet thermistor problem —
Whirlpool's wording: an issue with the control unit or
An issue with the user interface or its wiring
A problem with the main control board, the touchpad,
A problem with the motor, the control, or the wiring between them
A power failure interrupted the drying cycle
The control lock is on
Whirlpool's wording: the door has not been completely closed
The same digits mean different things on different equipment. Search the full code list
In more detail
About LG-built Kenmore dryer error code Ps
Whose code this actually is
Kenmore did not write Ps, because Kenmore has never built an appliance. This one is LG's, and it appears on the dryer that LG built and Sears sold under the Kenmore badge. Whirlpool, LG and Frigidaire all built dryers for this badge, and all three publish short two-character codes, so a lookup that skips the prefix is a coin toss dressed as an answer.
What it means
LG's own label is POWER ERROR.
Which Kenmore models can raise it
The Kenmore dryer whose model number begins 796 — the three digits before the period on the rating plate. Those digits are LG's, which is why LG's table is the one that applies to Ps and no other manufacturer's does.
What happens next
- Check the breaker — an electric dryer on one leg of supply tumbles and does not heat.
- This one is more often the house than the dryer.
Where this usually goes
The job this most often becomes is diagnostic visit, and that page carries a starting figure and the reasons that move it. A Kenmore dryer in South Florida is almost always on a long horizontal duct carrying humid air, and that duct is behind more heat and airflow codes here than any component inside the machine. Photograph the display before you cut the power: a reset clears Ps, and on a Kenmore the characters plus three digits off the plate are most of the diagnosis.
Where this meaning came from
LG's own documentation: LG Owner's Manual — WashTower WKEX200H*A / WKGX201H*A, P/No. MFL71485405. Kenmore publishes none of its own, which is why every entry on this site names the manufacturer's document instead.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards