Broward · South Florida
Kenmore repair in Fort Lauderdale
Waterfront houses, high-rises and everything between. Access varies more here than anywhere else in Broward, so the building or the street matters as much as the model when we plan the visit.
We cover Fort Lauderdale and the rest of Broward: an on-site diagnostic first, the price agreed in writing before anything is opened, and the exact figure confirmed once we have seen the unit.
By unit
What we repair in Fort Lauderdale, by Kenmore unit
Start with whichever matches yours. How an appliance is installed shapes the visit as much as the repair does, which is why we ask about it when you book.
-
Built-in · Kenmore and Kenmore Elite Kenmore dishwasher repair in Fort Lauderdale
Built-in dishwashers. 665 is the number on most of the plates we see and it is Whirlpool-built; 587 is Frigidaire and 630 is Bosch, and all three turn up in South Florida kitchens. Whirlpool publishes a real code scheme for these, which makes a dishwasher one of the more readable appliances on this badge — provided you read the code against the right builder's table.
- 665 is Whirlpool, 587 is Frigidaire, 630 is Bosch
- Drainage and wash performance are most of the calls
- The code on the display is Whirlpool's code
-
Top-load and front-load · 110 and 796 Kenmore washer repair in Fort Lauderdale
Laundry is where the decode matters most, because a Kenmore washer can be a Whirlpool, an an LG, and those are two genuinely different machines. A 110 and a 796 do not share a pump, a control board, a diagnostic sequence or a code table, and they do not fail the same way. The model number is not a formality on this appliance — it is the difference between the right visit and the wrong one.
- 110 is Whirlpool-built, 796 is LG-built
- Drain, spin and leaks are most of what we see
- Two washers under one badge, and two code tables
-
Electric and gas · 110, 796 and 417 Kenmore dryer repair in Fort Lauderdale
Electric and gas dryers built by Whirlpool, LG and Frigidaire under the badge. On this appliance the single most useful thing we can tell you is that a large share of no-heat and long-cycle calls are the vent rather than the dryer — and in South Florida houses the vent runs are longer, flatter and wetter than the ones these machines were designed around.
- 110 is Whirlpool-built, 796 is LG-built, 417 is Frigidaire-built
- The vent causes more of these calls than any part does
- Gas and electric fail in different places
-
Freestanding and slide-in · gas and electric Kenmore range repair in Fort Lauderdale
Freestanding and slide-in ranges, gas and electric. 790 is the number we see most and it is Frigidaire-built; 362 turns up on GE-built ranges and 911 on another range family altogether. A range is the appliance a household notices fastest when it stops, and it is also the one where the difference between a sensor, an element and a control board is the difference between a modest repair and a conversation about replacing it.
- 790 is Frigidaire, 362 is GE, 911 is a range prefix too
- Oven sensor and bake element are most of the calls
- Gas surface problems are usually the igniter, not the valve
-
Single and double · built into cabinetry Kenmore wall oven repair in Fort Lauderdale
Built-in wall ovens, single and double, mostly Frigidaire-built. What separates a wall oven from the oven in a range is not the cooking — it is the access. The appliance is fixed into joinery, often at height and often stacked with a microwave above it, and getting to the back of it is a real part of the job rather than a detail.
- Access is a genuine part of the work on these
- Sensor and element cover most of the calls
- A stacked installation changes the visit
-
Gas, radiant and induction · drop-in Kenmore cooktop repair in Fort Lauderdale
Drop-in cooktops — gas, radiant electric and induction. A cooktop is the simplest appliance in the kitchen on gas and one of the most electronic on induction, and the two share almost nothing but the hole they sit in. What they do share is that a single dead zone is usually a component rather than the whole appliance.
- One dead zone is rarely the whole cooktop
- Gas is mechanical, induction is electronic
- The glass itself is the one part we cannot repair
By job
The repairs we are called out for in Fort Lauderdale
Starting figures for this equipment in South Florida. What moves them is the model, the access and the part — the exact cost is confirmed after the on-site diagnostic.
-
from $125 Dishwasher wash performance service
Dishes coming out gritty, filmed or still wet. A large share of these are water, detergent and loading rather than the machine — and on South Florida water the film complaint in particular is usually chemistry rather than a component.
- Water temperature measured at the machine
- Spray arms and filter before any part
- Hard water addressed as hard water
-
from $225 Dishwasher pump replacement
Where the drain pump or the wash pump has genuinely failed rather than been blocked. The two do different jobs and produce different complaints — one leaves water behind, the other leaves dishes dirty — and telling them apart before ordering is most of the value here.
- Wash and drain pumps are different failures
- Blockage ruled out before a part is named
- The builder's own part number, sourced properly
-
from $145 Dishwasher drain repair
Standing water after a completed cycle. On a Whirlpool-built 665 this frequently arrives with a code on the display, and read against Whirlpool's own table it points at the drain path rather than at the pump — which is the difference between a filter clean and a part.
- The disposer plug checked before anything is opened
- The code read against the builder's own table
- The pump last, because it is usually not the pump
-
from $145 Door seal replacement
A gasket that has hardened, torn or stopped pulling the door shut. In a humid house this is not cosmetic: every hour a refrigerator seal leaks is an hour the defrost circuit spends clearing ice it should never have made, and on a front-load washer a tired gasket is where the smell complaints begin.
- Tested with paper rather than judged by eye
- The hinge and the alignment checked with it
- A seal is preventive work on this coast
-
from $155 Ice machine cleaning and descaling
The service that keeps a standalone ice machine alive in South Florida. Mineral collects on exactly the surfaces the machine depends on, output falls month by month without the machine ever stopping, and the interval printed in the manual assumes gentler water than we have.
- Output measured before and after
- The maker's own cleaner, on the maker's own cycle
- The cheapest service here and the most preventive
-
from $595 Sealed system repair
Compressor, condenser, evaporator and the refrigerant between them. It is real, it is the most expensive repair on a refrigerator, and it is quoted far more often than it happens. Everything cheaper is ruled out first, and on a mass-market cabinet we will tell you honestly when the repair no longer makes sense against the price of the appliance.
- Ruled in by measurement, never by elimination alone
- Licensed refrigerant work
- An honest replace-instead conversation where it applies
Nearby
Where else we work near Fort Lauderdale
Every place below has its own page, with what the equipment and the access are like there.
Neighborhoods in Fort Lauderdale
Elsewhere in Broward
In more detail
Kenmore repair in Fort Lauderdale, in more detail
What Kenmore equipment is like in Fort Lauderdale
Waterfront houses, high-rises and everything between. Access varies more here than anywhere else in Broward, so the building or the street matters as much as the model when we plan the visit.
Fort Lauderdale sits in Broward County, and the equipment here follows the housing: older kitchens with appliances fitted into openings that were cut for something else, and newer ones where they were specified with the cabinetry. Both are Kenmore work — cooktops, dishwashers, dryers — and both are diagnosed on site before anything is priced.
Salt, heat and storms — what they do to a kitchen full of appliances
Close to the water everything ages from the outside in. Salt corrodes the condenser coils and fan motors on the cold side and reaches burner caps, grates and igniters on the hot side, and both fail in the same way: a part that still works, slowly, until the day it does not. In Fort Lauderdale that turns a cleaning interval into a seasonal job rather than an annual one, on both halves of the kitchen.
What that means for the appliances in Fort Lauderdale
- Dryers — A condensation dryer exists because this kind of building does — nothing vents through an exterior wall, so the water goes to a drain or a tank instead. It also means a kinked condensate hose behind a stacked pair reads exactly like a dead heating element.
- Wall ovens — A wall oven in a tower is trimmed into a cabinet run with the building behind it, so removing it is planned rather than improvised, and the association usually wants notice before it happens.
- Ranges — Stainless that would stay clean inland pits within sight of the water, and the parts that suffer are the ones nobody looks at — burner caps, grate feet, the fixings behind a control panel.
- Refrigerator leaking water
- Oven not heating
- Washer will not drain
- Ice maker not making ice
- Dryer making noise
How a visit in Fort Lauderdale is arranged
We ask for the model number from the plate inside the door and a line about what the appliance is doing. That decides which parts ride in the van, and it is the difference between one appointment and two.
- In a building: the service elevator window, the loading bay and the hours contractors are allowed to work
- Behind a gate: how visitors are cleared, arranged before the appointment rather than at it
- Whether the doors are paneled to match the cabinetry, which changes how they come off and go back
- The diagnosis first, then the scope and the price in writing, and your approval before anything is opened
What it costs, and what moves the figure
Prices in Fort Lauderdale are the same as everywhere else we cover: a diagnostic from $95 that is credited toward the repair, and starting figures per job rather than one number for "a repair". What moves it is the model, how the appliance is built into the cabinetry, which part it needs and how quickly that part can be sourced — none of which can be judged over the phone. The repairs we carry out lists what each job involves and the figure it starts at, and the unit pages covers what tends to go wrong on each type.
The exact cost is confirmed after the on-site diagnostic and agreed with you before any work begins. We are an independent repair company — not affiliated with, authorized by, or endorsed by any manufacturer — and our warranty covers the labor we performed.
Before you book
Questions about a visit in Fort Lauderdale
Do you cover Fort Lauderdale?
Yes. Fort Lauderdale is in Broward County and inside the area we work every week. Give us the address when you book, and say how the Kenmore is installed — what has to come apart to reach it matters as much as where it is.
How soon can you get to Fort Lauderdale?
We will tell you the earliest slot we can genuinely keep rather than the earliest one that sounds good. Tell us the model number and what the unit is doing when you book: whether we can finish the same day depends on the part far more than on the drive.
Does it cost more because the job is in Fort Lauderdale?
No. The diagnostic and the work are priced the same across Miami-Dade, Broward and Palm Beach. What moves the figure is the model, how the unit is built in and which part it needs — never the address. Where access takes longer, we say so before anything is agreed rather than after.
My building has rules about service calls. What do you need?
The building name when you book, and anything it requires — a service elevator window, a loading bay slot, approved hours or a certificate of insurance. We arrange those in advance; found out on the day, they cost the appointment.
Booking a visit in Fort Lauderdale
Tell us the model number and what the unit is doing. We will bring the parts that problem usually needs, and you will have a firm price before we start.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards