Repair cost
Kenmore temperature sensor replacement cost
An inexpensive component and a diagnosis that has to be done properly, against the resistance table published by the company that built the appliance. Priced on establishing which sensor is lying rather than on the part itself.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
The short version
Where this figure comes from
A starting point for built-in appliances in South Florida, published so the number is not a mystery until somebody is standing in your kitchen.
Starts at
from $155
After a diagnostic from $95, which comes off the bill when you go ahead with the work.
or call (305) 680-1018
It is not
A quote for your unit
Exact cost
Confirmed after the on-site diagnostic
Warranty
On the labor we performed
What moves it
Why two of the same job cost different amounts
These apply at the same time and in both directions. Which of them is true of your kitchen is what the on-site diagnostic settles.
-
Which builder's table applies
A thermistor reads a resistance and that number means what the manufacturer's chart says it means. Whirlpool, LG and Frigidaire publish different charts. Read against the wrong one, a healthy sensor looks broken.
-
Refrigeration or cooking
A refrigerator thermistor and an oven sensor are the same idea in very different places. The oven one usually sits behind the rear liner and the refrigeration one inside the cabinet, and the access is what separates the figures.
-
How many sensors the appliance has
Multi-zone cabinets and double wall ovens have several, and finding which one has drifted means testing all of them. That is the work.
-
Whether the reading is drift or a break
An open circuit announces itself. A sensor that has drifted a few degrees produces an oven that browns wrong or a compartment that is slightly warm, and it is only found by comparison.
-
Whether it is the sensor or the control reading it
A perfect sensor into a bad input reads as a bad sensor. Which of the two it is decides whether this is a modest repair or a board conversation.
The work itself
What we actually do
The job behind the figure: what it involves, when a symptom points at it, and what we check first.
-
from $155 Temperature sensor replacement
The component that fails without looking like anything. A sensor that reports the wrong number makes an appliance hold a temperature it is not at, confidently and without complaint — a refrigerator that is warm while the display says it is cold, or an oven that is consistently twenty-five degrees out.
- Measured against a reference, not against the display
- A consistent offset is its signature
- Cheap to replace and easy to misdiagnose
In more detail
About Kenmore temperature sensor replacement cost
Why this is priced on the diagnosis
Because the component is cheap and being sure is not. A sensor is measured against a published resistance table at a known temperature, and the whole value of the visit is that the number is read against the right company's chart. This is the clearest case on the site of the general rule: on a badge-engineered appliance, knowing who built it is most of the diagnosis.
What a lying sensor looks like
A refrigerator that is a few degrees warm and insists it is not. A freezer that will not hold temperature while the compartment beside it is fine. An oven that browns one side, misses its set point by a consistent amount, or takes an implausible time to preheat. None of those announces itself as a sensor, which is why they are so often quoted as something larger.
The part that is not the sensor
Every one of these readings arrives at a control board, and a board with a bad input produces exactly the same symptom as a bad probe. Separating those two is done with measurements at both ends, and it decides whether you are looking at this figure or at the control board page.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Kenmore temperature sensor replacement cost
My oven runs hot. Is that the sensor?
It can be, and it can equally be calibration, which costs no part at all. Both are checked in the same visit and the calibration is checked first because it is free.
Is the part expensive?
Rarely. On every company behind this badge a temperature sensor is a modest component. What you are paying for is knowing which one to change and being right about it.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name