Broward · South Florida
Kenmore repair in Harbor Islands
Newer waterfront buildings with integrated kitchens and building access rules to match. Both are worth mentioning when you book.
Harbor Islands is a neighborhood of Hollywood, in Broward. We cover it on the same terms as the rest of the county: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
By unit
What we repair in Harbor Islands, by Kenmore unit
Start with whichever matches yours. How an appliance is installed shapes the visit as much as the repair does, which is why we ask about it when you book.
-
Top-load and front-load · 110 and 796 Kenmore washer repair in Harbor Islands
Laundry is where the decode matters most, because a Kenmore washer can be a Whirlpool, an an LG, and those are two genuinely different machines. A 110 and a 796 do not share a pump, a control board, a diagnostic sequence or a code table, and they do not fail the same way. The model number is not a formality on this appliance — it is the difference between the right visit and the wrong one.
- 110 is Whirlpool-built, 796 is LG-built
- Drain, spin and leaks are most of what we see
- Two washers under one badge, and two code tables
-
Single and double · built into cabinetry Kenmore wall oven repair in Harbor Islands
Built-in wall ovens, single and double, mostly Frigidaire-built. What separates a wall oven from the oven in a range is not the cooking — it is the access. The appliance is fixed into joinery, often at height and often stacked with a microwave above it, and getting to the back of it is a real part of the job rather than a detail.
- Access is a genuine part of the work on these
- Sensor and element cover most of the calls
- A stacked installation changes the visit
-
French door · side-by-side · top and bottom freezer Kenmore refrigerator repair in Harbor Islands
The appliance the badge is best known for, and the one where knowing who built it changes the repair most. A Kenmore refrigerator in a South Florida kitchen is a Whirlpool, a Frigidaire or an LG underneath, and the first three digits of the model number say which. That decides the parts, the diagnostic sequence and whether there is a published code table to read at all — so it is the first thing we ask for.
- 106 is Whirlpool, 253 is Frigidaire, 795 is LG
- Ice, water and the defrost circuit are most of the call volume
- The parts catalog is the builder's, not the badge's
-
Built-in · Kenmore and Kenmore Elite Kenmore dishwasher repair in Harbor Islands
Built-in dishwashers. 665 is the number on most of the plates we see and it is Whirlpool-built; 587 is Frigidaire and 630 is Bosch, and all three turn up in South Florida kitchens. Whirlpool publishes a real code scheme for these, which makes a dishwasher one of the more readable appliances on this badge — provided you read the code against the right builder's table.
- 665 is Whirlpool, 587 is Frigidaire, 630 is Bosch
- Drainage and wash performance are most of the calls
- The code on the display is Whirlpool's code
-
Freestanding and slide-in · gas and electric Kenmore range repair in Harbor Islands
Freestanding and slide-in ranges, gas and electric. 790 is the number we see most and it is Frigidaire-built; 362 turns up on GE-built ranges and 911 on another range family altogether. A range is the appliance a household notices fastest when it stops, and it is also the one where the difference between a sensor, an element and a control board is the difference between a modest repair and a conversation about replacing it.
- 790 is Frigidaire, 362 is GE, 911 is a range prefix too
- Oven sensor and bake element are most of the calls
- Gas surface problems are usually the igniter, not the valve
-
Under-cabinet and chimney · ducted and recirculating Kenmore range hood repair in Harbor Islands
Under-cabinet and chimney hoods, and this is the one appliance on the badge with a ventilation specialist behind it — the 233 prefix is Broan. There is not much to a hood: a motor, a switch, a lamp and a path for the air. Which is why most of what we are called about turns out to be the duct or the filters rather than the hood.
- 233 is Broan-built — a ventilation maker, not an appliance one
- Most complaints are the duct or the filters
- Recirculating hoods cannot extract, by design
By job
The repairs we are called out for in Harbor Islands
Starting figures for this equipment in South Florida. What moves them is the model, the access and the part — the exact cost is confirmed after the on-site diagnostic.
-
from $155 Temperature sensor replacement
The component that fails without looking like anything. A sensor that reports the wrong number makes an appliance hold a temperature it is not at, confidently and without complaint — a refrigerator that is warm while the display says it is cold, or an oven that is consistently twenty-five degrees out.
- Measured against a reference, not against the display
- A consistent offset is its signature
- Cheap to replace and easy to misdiagnose
-
from $225 Dishwasher pump replacement
Where the drain pump or the wash pump has genuinely failed rather than been blocked. The two do different jobs and produce different complaints — one leaves water behind, the other leaves dishes dirty — and telling them apart before ordering is most of the value here.
- Wash and drain pumps are different failures
- Blockage ruled out before a part is named
- The builder's own part number, sourced properly
-
from $155 Washer leak repair
Water on the floor, which is rarely where the leak is. We work from where it lands back to where it comes from — the door gasket, the dispenser, the hoses, the tub seal — because a leak diagnosed by the puddle is a leak diagnosed wrong.
- Traced back rather than guessed at
- Fill hoses checked while we are there, every time
- The gasket fold is a local suspect here
-
from $185 Gas dryer igniter replacement
A gas dryer that tumbles cold. The igniter, the flame sensor and the gas valve coils are the usual sequence, and they are tested rather than swapped — all three produce the same complaint and only one of them is the answer.
- Igniter flame sensor and coils tested in order
- Gas work done by somebody licensed to do it
- The vent checked here too
-
from $155 Cooktop element repair
One radiant zone dead while the others work. That pattern is good news: it points at that element or its switch rather than at anything shared, and both are accessible parts on most of these cooktops.
- One dead zone is rarely a board
- Element and switch tested separately
- Cracked glass is a stop rather than a repair
-
from $95 OEM cross reference and parts sourcing
The job that only exists on a badge-engineered appliance. A Kenmore part number is not the part number the factory used, and on a discontinued unit the difference decides whether the repair is possible at all. We cross-reference the Kenmore number to the builder's own number and tell you plainly whether the part is current, superseded or gone.
- The builder's part number, not the badge's
- Superseded numbers traced rather than guessed
- An honest answer when a part no longer exists
Nearby
Where else we work near Harbor Islands
Every place below has its own page, with what the equipment and the access are like there.
Elsewhere in Broward
In more detail
Kenmore repair in Harbor Islands, in more detail
What Kenmore equipment is like in Harbor Islands
Newer waterfront buildings with integrated kitchens and building access rules to match. Both are worth mentioning when you book.
Harbor Islands is part of Hollywood, in Broward County, and we treat it as its own call rather than a line on a map: the buildings, the access and the age of the installations differ enough from the rest of the city to change how a visit is planned. What does not change is the work — Kenmore cooktops, dishwashers, dryers, diagnosed on site before anything is priced.
Salt, heat and storms — what they do to a kitchen full of appliances
Close to the water everything ages from the outside in. Salt corrodes the condenser coils and fan motors on the cold side and reaches burner caps, grates and igniters on the hot side, and both fail in the same way: a part that still works, slowly, until the day it does not. In Harbor Islands that turns a cleaning interval into a seasonal job rather than an annual one, on both halves of the kitchen.
What that means for the appliances in Harbor Islands
- Dryers — A condensation dryer exists because this kind of building does — nothing vents through an exterior wall, so the water goes to a drain or a tank instead. It also means a kinked condensate hose behind a stacked pair reads exactly like a dead heating element.
- Range hoods — Almost nothing in a tower vents outside, so the hood recirculates and lives entirely on a charcoal filter — a consumable most owners have never been told about, and the reason a healthy-sounding hood can move nothing at all.
- Refrigerators — A refrigerator in a tower has less air around it and a warmer cabinet behind it than the same unit in a house, so the condenser matters more here and the cleaning interval is shorter than the manual assumes.
- Frost building up in the freezer
- Oven door locked shut
- Washer will not spin
- Refrigerator leaking water
- Oven not heating
How a visit in Harbor Islands is arranged
We ask for the model number from the plate inside the door and a line about what the appliance is doing. That decides which parts ride in the van, and it is the difference between one appointment and two.
- In a building: the service elevator window, the loading bay and the hours contractors are allowed to work
- Behind a gate: how visitors are cleared, arranged before the appointment rather than at it
- Whether the doors are paneled to match the cabinetry, which changes how they come off and go back
- The diagnosis first, then the scope and the price in writing, and your approval before anything is opened
What it costs, and what moves the figure
Prices in Harbor Islands are the same as everywhere else we cover: a diagnostic from $95 that is credited toward the repair, and starting figures per job rather than one number for "a repair". What moves it is the model, how the appliance is built into the cabinetry, which part it needs and how quickly that part can be sourced — none of which can be judged over the phone. The repairs we carry out lists what each job involves and the figure it starts at, and the unit pages covers what tends to go wrong on each type.
The exact cost is confirmed after the on-site diagnostic and agreed with you before any work begins. We are an independent repair company — not affiliated with, authorized by, or endorsed by any manufacturer — and our warranty covers the labor we performed.
Before you book
Questions about a visit in Harbor Islands
Do you cover Harbor Islands?
Yes. Harbor Islands is part of Hollywood, in Broward County, and it is inside the area we work every week. Give us the address when you book, and say how the Kenmore is installed — what has to come apart to reach it matters as much as where it is.
How soon can you get to Harbor Islands?
We will tell you the earliest slot we can genuinely keep rather than the earliest one that sounds good. Tell us the model number and what the unit is doing when you book: whether we can finish the same day depends on the part far more than on the drive.
Does it cost more because the job is in Harbor Islands?
No. The diagnostic and the work are priced the same across Miami-Dade, Broward and Palm Beach. What moves the figure is the model, how the unit is built in and which part it needs — never the address. Where access takes longer, we say so before anything is agreed rather than after.
My building has rules about service calls. What do you need?
The building name when you book, and anything it requires — a service elevator window, a loading bay slot, approved hours or a certificate of insurance. We arrange those in advance; found out on the day, they cost the appointment.
Booking a visit in Harbor Islands
Tell us the model number and what the unit is doing. We will bring the parts that problem usually needs, and you will have a firm price before we start.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards