Palm Beach · South Florida
Kenmore repair in Wellington
Equestrian properties and family neighborhoods, many with a second kitchen or a utility room well away from the main one. Those are the appliances that go unnoticed longest.
We cover Wellington and the rest of Palm Beach: an on-site diagnostic first, the price agreed in writing before anything is opened, and the exact figure confirmed once we have seen the unit.
By unit
What we repair in Wellington, by Kenmore unit
Start with whichever matches yours. How an appliance is installed shapes the visit as much as the repair does, which is why we ask about it when you book.
-
Top-load and front-load · 110 and 796 Kenmore washer repair in Wellington
Laundry is where the decode matters most, because a Kenmore washer can be a Whirlpool, an an LG, and those are two genuinely different machines. A 110 and a 796 do not share a pump, a control board, a diagnostic sequence or a code table, and they do not fail the same way. The model number is not a formality on this appliance — it is the difference between the right visit and the wrong one.
- 110 is Whirlpool-built, 796 is LG-built
- Drain, spin and leaks are most of what we see
- Two washers under one badge, and two code tables
-
Single and double · built into cabinetry Kenmore wall oven repair in Wellington
Built-in wall ovens, single and double, mostly Frigidaire-built. What separates a wall oven from the oven in a range is not the cooking — it is the access. The appliance is fixed into joinery, often at height and often stacked with a microwave above it, and getting to the back of it is a real part of the job rather than a detail.
- Access is a genuine part of the work on these
- Sensor and element cover most of the calls
- A stacked installation changes the visit
-
French door · side-by-side · top and bottom freezer Kenmore refrigerator repair in Wellington
The appliance the badge is best known for, and the one where knowing who built it changes the repair most. A Kenmore refrigerator in a South Florida kitchen is a Whirlpool, a Frigidaire or an LG underneath, and the first three digits of the model number say which. That decides the parts, the diagnostic sequence and whether there is a published code table to read at all — so it is the first thing we ask for.
- 106 is Whirlpool, 253 is Frigidaire, 795 is LG
- Ice, water and the defrost circuit are most of the call volume
- The parts catalog is the builder's, not the badge's
-
Built-in · Kenmore and Kenmore Elite Kenmore dishwasher repair in Wellington
Built-in dishwashers. 665 is the number on most of the plates we see and it is Whirlpool-built; 587 is Frigidaire and 630 is Bosch, and all three turn up in South Florida kitchens. Whirlpool publishes a real code scheme for these, which makes a dishwasher one of the more readable appliances on this badge — provided you read the code against the right builder's table.
- 665 is Whirlpool, 587 is Frigidaire, 630 is Bosch
- Drainage and wash performance are most of the calls
- The code on the display is Whirlpool's code
-
Freestanding and slide-in · gas and electric Kenmore range repair in Wellington
Freestanding and slide-in ranges, gas and electric. 790 is the number we see most and it is Frigidaire-built; 362 turns up on GE-built ranges and 911 on another range family altogether. A range is the appliance a household notices fastest when it stops, and it is also the one where the difference between a sensor, an element and a control board is the difference between a modest repair and a conversation about replacing it.
- 790 is Frigidaire, 362 is GE, 911 is a range prefix too
- Oven sensor and bake element are most of the calls
- Gas surface problems are usually the igniter, not the valve
-
Under-cabinet and chimney · ducted and recirculating Kenmore range hood repair in Wellington
Under-cabinet and chimney hoods, and this is the one appliance on the badge with a ventilation specialist behind it — the 233 prefix is Broan. There is not much to a hood: a motor, a switch, a lamp and a path for the air. Which is why most of what we are called about turns out to be the duct or the filters rather than the hood.
- 233 is Broan-built — a ventilation maker, not an appliance one
- Most complaints are the duct or the filters
- Recirculating hoods cannot extract, by design
By job
The repairs we are called out for in Wellington
Starting figures for this equipment in South Florida. What moves them is the model, the access and the part — the exact cost is confirmed after the on-site diagnostic.
-
from $165 Surface igniter replacement
A gas burner that clicks and clicks and will not light. Clicking means the spark system is alive and trying, which rules out a great deal — and it is very often the burner cap seating or a blocked port rather than the igniter at all.
- Cap seating and ports checked first, for free
- Igniter tested rather than assumed
- The gas valve is rarely the answer
-
from $125 Appliance maintenance
Scheduled work in one visit rather than an emergency in three months. Condenser coils, door seals, filters, the dryer duct and the dishwasher drain path — the things that fail quietly here and take a component with them when they do. In this climate this is the service that changes the arithmetic most.
- Coils, seals, filters and the duct in one visit
- Priced below a diagnosis plus the repair it prevents
- The interval that suits South Florida rather than the manual
-
from $155 Temperature sensor replacement
The component that fails without looking like anything. A sensor that reports the wrong number makes an appliance hold a temperature it is not at, confidently and without complaint — a refrigerator that is warm while the display says it is cold, or an oven that is consistently twenty-five degrees out.
- Measured against a reference, not against the display
- A consistent offset is its signature
- Cheap to replace and easy to misdiagnose
-
from $135 Dishwasher door latch repair
A dishwasher that will not start, or that stops partway through, when the real problem is that the machine cannot confirm its door is shut. The latch and its switch are cheap and they fail far more often than a control board does.
- The commonest cause of a dishwasher that will not start
- Switch tested rather than the board blamed
- The door alignment checked in the same visit
-
from $165 Dryer drum roller and belt repair
A dryer that squeals, thumps, or turns over without the drum moving. The belt, the rollers and the idler wear together and replacing one of the three on its own usually buys a few months.
- Belt rollers and idler replaced as a set
- The noise identified before anything is opened
- Cheap parts and a real amount of labor
-
from $235 Induction cooktop repair
An induction top that shuts down mid-cook, refuses a pan, or has lost a zone. More of these turn out to be heat and ventilation than electronics — the power stage lives under the glass and is cooled by a fan, and a cabinet that traps warm air makes a healthy cooktop protect itself.
- Ventilation checked before any board
- Pan compatibility is a real answer, not a brush-off
- One dead zone points at that zone's coil or driver
Nearby
Where else we work near Wellington
Every place below has its own page, with what the equipment and the access are like there.
Elsewhere in Palm Beach
In more detail
Kenmore repair in Wellington, in more detail
What Kenmore equipment is like in Wellington
Equestrian properties and family neighborhoods, many with a second kitchen or a utility room well away from the main one. Those are the appliances that go unnoticed longest.
Wellington sits in Palm Beach County, and the equipment here follows the housing: older kitchens with appliances fitted into openings that were cut for something else, and newer ones where they were specified with the cabinetry. Both are Kenmore work — cooktops, dishwashers, dryers — and both are diagnosed on site before anything is priced.
Heat, dust and power cuts — what they do to a kitchen full of appliances
Inland the enemy is heat, dust and grease rather than salt. Condensers run hard for more months of the year here than almost anywhere else in the country, and grease that condenses in a hood liner instead of leaving through it comes back as a fan that labors. In Wellington the appliances we are called out to are usually working exactly as designed — in conditions nobody designed them for.
What that means for the appliances in Wellington
- Houses here often run more than one of the same appliance, and the second one is the one that goes unnoticed longest. If there is a second at the address, say so when you book — seeing both on one visit costs less than two visits.
- Refrigerators — Inland the enemy is dust and heat rather than salt: condensers pack with it, and nothing about a unit that is slowly running warmer announces itself until the summer.
- Washers — A laundry room here is a real room rather than a closet, which usually makes the appointment shorter and the diagnosis easier — there is somewhere to stand.
- Dryer with no heat
- Washer leaking
- Dishwasher will not start
- Standalone ice maker making less ice
- Ice maker not making ice
How a visit in Wellington is arranged
We ask for the model number from the plate inside the door and a line about what the appliance is doing. That decides which parts ride in the van, and it is the difference between one appointment and two.
- How the appliance is built in, and whether it has ever been pulled out before
- Whether there is a second one — a bar, a pantry, a garage or an outdoor kitchen
- Whether the doors are paneled to match the cabinetry, which changes how they come off and go back
- The diagnosis first, then the scope and the price in writing, and your approval before anything is opened
What it costs, and what moves the figure
Prices in Wellington are the same as everywhere else we cover: a diagnostic from $95 that is credited toward the repair, and starting figures per job rather than one number for "a repair". What moves it is the model, how the appliance is built into the cabinetry, which part it needs and how quickly that part can be sourced — none of which can be judged over the phone. The repairs we carry out lists what each job involves and the figure it starts at, and the unit pages covers what tends to go wrong on each type.
The exact cost is confirmed after the on-site diagnostic and agreed with you before any work begins. We are an independent repair company — not affiliated with, authorized by, or endorsed by any manufacturer — and our warranty covers the labor we performed.
Before you book
Questions about a visit in Wellington
Do you cover Wellington?
Yes. Wellington is in Palm Beach County and inside the area we work every week. Give us the address when you book, and say how the Kenmore is installed — what has to come apart to reach it matters as much as where it is.
How soon can you get to Wellington?
We will tell you the earliest slot we can genuinely keep rather than the earliest one that sounds good. Tell us the model number and what the unit is doing when you book: whether we can finish the same day depends on the part far more than on the drive.
Does it cost more because the job is in Wellington?
No. The diagnostic and the work are priced the same across Miami-Dade, Broward and Palm Beach. What moves the figure is the model, how the unit is built in and which part it needs — never the address. Where access takes longer, we say so before anything is agreed rather than after.
What do you need from me before the visit in Wellington?
The model number from the data plate, a photograph of the display if anything is showing on it, and a line about what the unit is doing. Those three decide which parts a technician brings, and they are the difference between one visit and two.
Booking a visit in Wellington
Tell us the model number and what the unit is doing. We will bring the parts that problem usually needs, and you will have a firm price before we start.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards