Service
Kenmore oven element replacement
An oven that will not reach temperature, or one that browns the top and never cooks through. A failed bake element often shows it — a blister, a break, a bright spot — and it is one of the few appliance repairs where looking is genuinely diagnostic.
- From $95 diagnostic, credited to the repair
- 59 cities and neighborhoods covered
- OEM parts available on order
- In writing the price, before anything is opened
Before you read on
What this job costs and how it is agreed
A starting figure, not a quote. What moves it is the model, how the unit is built in and which part it needs — settled after the on-site diagnostic.
Starts at
from $165
After a diagnostic from $95, which comes off the bill when you go ahead.
or call (305) 680-1018
Diagnostic
From $95, credited to the repair
The price
In writing, before anything is opened
Warranty
On the labor we performed
On the visit
How this visit actually goes
The same order every time, so nothing is opened and nothing is charged before you have seen the figure and said yes.
-
01
Look at both elements
Bake and broil. An oven running on broil alone browns and does not cook, which is a very specific complaint.
-
02
Test rather than trust the look
Continuity, because an element can be open without any visible damage.
-
03
Rule out the sensor and the control
An oven that is not heating and an oven that thinks it is already hot look the same from the kitchen.
-
04
Fit and secure
With the terminals in good condition. Burnt terminals take the new element with them.
-
05
Bring it to temperature and measure
Against an independent probe, held, not just reached.
Applies to
The Kenmore units we carry this work out on
-
Freestanding and slide-in · gas and electric Kenmore range repair in Miami
Freestanding and slide-in ranges, gas and electric. 790 is the number we see most and it is Frigidaire-built; 362 turns up on GE-built ranges and 911 on another range family altogether. A range is the appliance a household notices fastest when it stops, and it is also the one where the difference between a sensor, an element and a control board is the difference between a modest repair and a conversation about replacing it.
- 790 is Frigidaire, 362 is GE, 911 is a range prefix too
- Oven sensor and bake element are most of the calls
- Gas surface problems are usually the igniter, not the valve
-
Single and double · built into cabinetry Kenmore wall oven repair in Miami
Built-in wall ovens, single and double, mostly Frigidaire-built. What separates a wall oven from the oven in a range is not the cooking — it is the access. The appliance is fixed into joinery, often at height and often stacked with a microwave above it, and getting to the back of it is a real part of the job rather than a detail.
- Access is a genuine part of the work on these
- Sensor and element cover most of the calls
- A stacked installation changes the visit
In more detail
About Kenmore oven element replacement
About oven elements on a range and in a stack
Most of this figure is access rather than the component. On a freestanding range the element is reached from inside the cavity with the machine pulled forward; on a wall oven built into cabinetry, particularly a double, the appliance comes out of the opening and goes back in true. The part is nearly identical and the visit is not. Which element has gone is decided by which function stopped — bake, broil or convection — rather than by looking, because elements fail open with no visible mark and a meter finds in seconds what an eye never will.
This article is based on:
- Official manufacturer documentation
- Internal repair procedures
- Technician repair history
- Company quality standards
Before you book
Questions about Kenmore oven element replacement
The cooktop works and the oven does not.
That sentence has already separated two circuits, which is genuinely useful. It points at the oven side — element, sensor or control — rather than anything shared.
It looks perfectly fine. Can it still be broken?
Easily. An element can fail anywhere along its length with no visible damage. Visual inspection is the least reliable test on this repair.
Where we do it
Across Miami-Dade, Broward, and Palm Beach
Same terms everywhere we go: an on-site diagnostic first, the price agreed in writing, and the exact figure confirmed once we have seen the unit.
Neighborhoods people ask for by name